Radio Shack Regulated Power Supply Specifikace

HTX-202 (190-1120) Specifications Faxback Doc. # 15723 GENERAL Frequency Range:...

programs. CONNECTING THE ANTENNA Your transceiver comes with a flexible antenna. You must connect an antenna to your transceiver before you transmi

connect an external microphone, the internal microphone does not work, but the internal PTT is not affected. If your microphone has a 3/32 inch(2.5

transceiver. 1. Turn off the transceiver. 2. Press and hold down F+CLR. Then, turn on the transceiver. USING THE LIGHT Press L on the

1. Turn on the transceiver. 2. Press VF. 3. Use the keypad to enter the last four digits of the frequency. For example, to enter 146.940, pr

Scan limits: 144 MHz to 148 MHz To stop scanning, press \/SC, /\SC, CA, PR, VF, or turn off the transceiver. SCANNING FOR A VACANT F

2. Select the desired frequency. 3. If + or - is on the display, repeatedly press F & + / - until neither symbol appears. 4. Press LOW PO

SETTING THE KEY ENTRY BEEP Each time you press a key, the transceiver sounds a beep. To turn off the beep, press F+BEEP. The key beep does not sou

press F+T-SQL so that T-SQL appears on the display. NOTE: If you turn on T-SQL you must correctly set both the transmit subaudibl

frequency memory display. To use the calling frequency memory, press CA at any time. The transceiver immediately goes to the calling frequency

To continuously scan the three priority frequency memories, press PR. Then, press and hold down /\SC or \/SC at least 1 second, NOTE: You must stor

Threshold:...0.1uV Tight:...10 dB above threshold

Follow these steps to clear a memory. 1. Press PR or MR and select the memory you want to clear. 2. Press F+M-CLR to clear the settings stored in t

Your transceiver has a configuration menu that lets you modify operation settings. Each of the following sections explain how and when to use each c

repeaters receive at a frequency 600 kHz lower or higher than they retransmit (repeat) on. For example, if a repeater's input frequency is 146.3

---------------- ---------------- | tc oFF | | rc oFF | ---------------- ------------

M4 225.7 34 M5 233.6 35 M6 241.8 36 M7 250.3 37 SETTING SCAN OPTIONS Several configuration menu items control how your transcei

To change the resume condition, follow the steps in "Understanding the Configuration Menu" to display Sc. Then, rotate TUNE to select the r

To set the transceiver to save power press F+SAVE so that SAVE appears on the display. In the power-save mode, the transceiver turns on the receiver

"Understanding the Configuration Menu" to display Lb. Then, rotate TUNE to select 4, 8, 12, or 16 seconds. USING TOUCH-TONE FEATURES Your

NOTE: To enter a D, press D twice. TRANSMITTING A DTMF MEMORY SEQUENCE To send a DTMF memory sequence, press and hold down PTT. Then, press D foll

AUTOMATICALLY SENDING A DTMF REPLY You can set your transceiver to automatically transmit the touch-tone digit (#) when you have enabled DTMF squelch

7.2V DC:...0.8A 9V DC:...0.95A

authorization to operate the transceiver. If your transceiver is not performing as it should, take it to your local Radio Shack store. Error Codes

external antenna. When pressing f/3, it only comes up with a negative offset. In order to come up with a positive offset, check the offset by enteri

rotate tune to set frequency. you can set tones to off for receive subaudible tone frequency press star twice rotate tu

lets you set a Sub-audible tone that your transceiver must receive to open

preparation You can operate your transceiver from any of the following sources: Rechargeable power pack (supplied with charger)

NOTES: Nickel-cadmium batteries deliver more power if you occasionally let them completely discharge. To do this, use the transceiver until

3. Press the battery holder into the battery holder case. When power is low, BATT appears when you press PTT. Be sure to use six fresh AA alkaline

Follow these steps to power the transceiver from the 1-amp, 12 volt DC adapter. 1. Connect the barrel plug with the tip set to positive. 2. Insert

4. Melt a small amount of solder onto the other end of the wire. Then, connect the red lead to the power supply's + terminal and connect t